Saturday, April 17, 2010

CHEMICAL REACTION ENGINEERING

Every industrial chemical process is designed to produce economically a desired
product from a variety of starting materials through a succession of treatment
steps. Figure 1.1 shows a typical situation. The raw materials undergo a number
of physical treatment steps to put them in the form in which they can be reacted
chemically. Then they pass through the reactor. The products of the reaction
must then undergo further physical treatment-separations, purifications, etc.-
for the final desired product to be obtained.
Design of equipment for the physical treatment steps is studied in the unit
operations. In this book we are concerned with the chemical treatment step of
a process. Economically this may be an inconsequential unit, perhaps a simple
mixing tank. Frequently, however, the chemical treatment step is the heart of
the process, the thing that makes or breaks the process economically.
Design of the reactor is no routine matter, and many alternatives can be
proposed for a process. In searching for the optimum it is not just the cost of
the reactor that must be minimized. One design may have low reactor cost, but
the materials leaving the unit may be such that their treatment requires a much
higher cost than alternative designs. Hence, the economics of the overall process
must be considered.
Reactor design uses information, knowledge, and experience from a variety
of areas-thermodynamics, chemical kinetics, fluid mechanics, heat transfer,
mass transfer, and economics. Chemical reaction engineering is the synthesis of
all these factors with the aim of properly designing a chemical reactor.
To find what a reactor is able to do we need to know the kinetics, the contacting
pattern and the performance equation.

Classification of Reactions
There are many ways of classifying chemical reactions. In chemical reaction
engineering probably the most useful scheme is the breakdown according to
the number and types of phases involved, the big division being between the
homogeneous and heterogeneous systems. A reaction is homogeneous if it takes
place in one phase alone. A reaction is heterogeneous if it requires the presence
of at least two phases to proceed at the rate that it does. It is immaterial whether
the reaction takes place in one, two, or more phases; at an interface; or whether
the reactants and products are distributed among the phases or are all contained
within a single phase. All that counts is that at least two phases are necessary
for the reaction to proceed as it does.
Sometimes this classification is not clear-cut as with the large class of biological
reactions, the enzyme-substrate reactions. Here the enzyme acts as a catalyst in
the manufacture of proteins and other products. Since enzymes themselves are
highly complicated large-molecular-weight proteins of colloidal size, 10-100 nm,
enzyme-containing solutions represent a gray region between homogeneous and
heterogeneous systems. Other examples for which the distinction between homogeneous
and heterogeneous systems is not sharp are the very rapid chemical
reactions, such as the burning gas flame. Here large nonhomogeneity in composition
and temperature exist. Strictly speaking, then, we do not have a single phase,
for a phase implies uniform temperature, pressure, and composition throughout.
The answer to the question of how to classify these borderline cases is simple.
It depends on how we choose to treat them, and this in turn depends on which description we think is more useful. Thus, only in the context of a given situation
can we decide how best to treat these borderline cases.
Cutting across this classification is the catalytic reaction whose rate is altered
by materials that are neither reactants nor products. These foreign materials,
called catalysts, need not be present in large amounts. Catalysts act somehow as
go-betweens, either hindering or accelerating the reaction process while being
modified relatively slowly if at all.
Table 1.1 shows the classification of chemical reactions according to our scheme
with a few examples of typical reactions for each type.
Variables Affecting the Rate of Reaction
Many variables may affect the rate of a chemical reaction. In homogeneous
systems the temperature, pressure, and composition are obvious variables. In
heterogeneous systems more than one phase is involved; hence, the problem
becomes more complex. Material may have to move from phase to phase during
reaction; hence, the rate of mass transfer can become important. For example,
in the burning of a coal briquette the diffusion of oxygen through the gas film
surrounding the particle, and through the ash layer at the surface of the particle,
can play an important role in limiting the rate of reaction. In addition, the rate
of heat transfer may also become a factor. Consider, for example, an exothermic
reaction taking place at the interior surfaces of a porous catalyst pellet. If the
heat released by reaction is not removed fast enough, a severe nonuniform
temperature distribution can occur within the pellet, which in turn will result in
differing point rates of reaction. These heat and mass transfer effects become
increasingly important the faster the rate of reaction, and in very fast reactions,
such as burning flames, they become rate controlling. Thus, heat and mass transfer
may play important roles in determining the rates of heterogeneous reactions.

Definition of Reaction Rate

We next ask how to define the rate of reaction in meaningful and useful ways.
To answer this, let us adopt a number of definitions of rate of reaction, all interrelated and all intensive rather than extensive measures. But first we must
select one reaction component for consideration and define the rate in terms of
this component i. If the rate of change in number of moles of this component
due to reaction is dN,ldt, then the rate of reaction in its various forms is defined
as follows. Based on unit volume of reacting fluid,
For the full article, send us email at milleniiumtutors@yahoo.com


No comments:

Post a Comment

Analyst